Messages

721

User Zone / Re: Graphics Card install

« on: December 01, 2019, 03:43:34 pm »

ok I immediately try and let you know, thank you very much

722

User Zone / Re: Graphics Card install

« on: December 01, 2019, 03:16:44 pm »

wait let me understand, the command modeprobe blacklist I have to put it in the petit boot so I should get out of the operating system, go back to petit boot, exit the list of initial options and where it allows me to type I have to enter the command modeprobe.blacklist, I got it right?

723

User Zone / Re: Graphics Card install

« on: December 01, 2019, 02:41:45 pm »

the command I executed, the list is very long and does not go all into a post, I created a file with libreoffice and inserted it all into that file. I didn't post it right away because I was trying with the modeprobe command but it doesn't work because it asks me to specify an argument like -d, -e etc. etc. I try to post the file containing the dmesg command

724

User Zone / Re: Graphics Card install

« on: December 01, 2019, 01:30:02 pm »

I entered that command you told me but it tells me unknown command, I am in root mode in the command shell. I entered modprobe.blacklist = ast video = offb:
says that modeprobe.blacklist is an unknown command ...

725

User Zone / Re: Graphics Card install

« on: December 01, 2019, 10:16:12 am »

Hi, I currently use the HDMI video output integrated in the blackbird obviously because it's the only one I can use because if I try to insert the HDMI cable into the 5700 XT output, it doesn't work at the moment. I will try to execute that command and send the result here in the discussion and we'll see what the system says. Thanks

726

Blackbird / HDMI output for mother board

« on: December 01, 2019, 09:38:35 am »

Hi everyone, I open this other discussion because I have a problem that I also mentioned in Raptor, regarding the HDMI output of the card. In practice, sometimes when you load the firmware when the power switch is turned on, when you load and send the video of what you are doing, nothing appears. The system continues to function regularly and you can hear the end of the petit boot loading but the video cannot be seen. If I turn off the stand-by button then reloading there is the same problem, while if I turn off the main power supply switch and then switch the bmc firmware back on before booting, then it works again, so I think that is a bug in the current bmc firmware that causes this annoying problem. Today he did it 3 times in a row before returning to work regularly. Are any of you experiencing the same problem?

727

User Zone / Re: Graphics Card install

« on: December 01, 2019, 07:40:41 am »

Maybe I didn't know how to explain myself. I don't know the procedure you're talking about, unfortunately I'm not a Linux expert, I'm just learning to use it now. I need to understand simply how I can activate my AMD Radeon 5700 XT GPU, which the system recognizes perfectly (including 3D acceleration). I need to figure out how to tell the system, which has to use that to give me the video output, thus activating me, both the HDMI output and the others present in the graphics card. My problem is only this ... If there is also the procedure for Ubuntu it is fine as well, I have also installed the one in another HD, I am mainly interested in Fedora but if you know it for Ubuntu, it's ok anyway, meanwhile I begin to understand how to use the GPU ... Thanks

728

User Zone / Re: Graphics Card install

« on: November 30, 2019, 06:10:01 pm »

I also imagined that Fedora 31 already had something pre-installed since the card is recognized perfectly, the problem is that I don't know how to activate it, I can't understand how to make it operational ... Raptor says that from the next firmware of the Blackbird, it will be possible to activate it but they also say that we have to wait for the Q1 of 2020 which I think is a bit long to wait and so I wanted to understand if it was possible to do it already without the need to wait for the new firmware ...

729

User Zone / Re: Graphics Card install

« on: November 30, 2019, 02:03:42 pm »

Hi, thanks for the reply, I'm using Fedora 31, recognize my AMD 5700 XT Navi 10 card, I just have to activate it and make it work because at the moment I still haven't managed to make it work and I still have to use the Blackbird HDMI video output . As an ambitious use of GNOME and I like it a lot, I am very well. Raptor told me to take the binaries that are currently related to my GPU and put them all in lib / firmware / amdgpu, only I don't know where to find this path, I didn't understand how to do ...

730

User Zone / Graphics Card install

« on: November 30, 2019, 04:39:07 am »

Hi everyone, I would like to use my graphics card on my Blackbird system but I didn't understand some passages. They tell me to take the files with the .BIN extension and put them in / lib / firmware / amdgpu but the problem is that I don't know where to take this line or directory, I didn't understand what the / lib / firmware / amdgpu line is exactly, how to put all the .BIN files downloaded. Does anyone know how to proceed? Thanks

731

Condor / Re: Technical features

« on: November 29, 2019, 05:06:20 pm »

Yes, this page I had already read, I wanted to understand certain things specifically that unfortunately is not found on this internet page

732

Condor / Technical features

« on: November 27, 2019, 03:08:49 pm »

Hi everyone, Raptor does not tell us anything about this beautiful card, I would like to understand for example if it will mount HDMI video output and 5.1 audio output or for these features you will have to resort to the additional cards ...

733

General OpenPOWER Discussion / Re: Ahoy shipmates!

« on: November 26, 2019, 02:39:48 pm »

hello everyone, I too am now part of this beautiful forum! Viva Power and long live IBM / Raptor!