Messages

16

General OpenPOWER Discussion / Re: USB keyboards not working in petitboot bootloader environment

« on: September 13, 2022, 04:51:58 pm »

Maybe petiboot isn't loading the USBHID driver? I've been able to directly login to the bootloader.
IIRC, hvc0 is for connecting a terminal to the Rs232 serial port.

17

User Zone / Re: Void Linux thread

« on: July 25, 2022, 12:43:09 am »

What BMC version do you have? did you see this in the quick start...?

Please note that older releases of BMC firmware had an issue where the IP could not be set. If you run the commands listed below but the IP information does not change (and you cannot work with the factory defaults), upgrade your BMC as explained in https://wiki.raptorcs.com/wiki/Talos_II/Firmware.

18

Blackbird / Re: Did my Blackbird just die on me?

« on: July 16, 2022, 05:34:16 pm »

The TalosII schematic shows pin26 F20 of the BMC to be an input, SYS_PWROK_BUF, from the FPGA.

19

Blackbird / Re: Did my Blackbird just die on me?

« on: July 14, 2022, 04:04:41 pm »

Looks like the BMC is failing to setup an IO pin.
Just a guess but maybe there's short at a button, connector, or the pins on BMC IC.

20

Operating Systems and Porting / Re: [NEWS] AlmaLinux 8.5 now supports PowerPC

« on: March 19, 2022, 11:09:45 pm »

Looks like the different flavors are options within the same install media (don't have their own ISO's). I got it working now.

I had two SAS drives plugged in which the installer doesn't seem to like if they're both plugged in, for some reason.
Maybe because the RAID or ESXI setup they had before?

21

Operating Systems and Porting / Re: [NEWS] AlmaLinux 8.5 now supports PowerPC

« on: March 19, 2022, 05:28:51 pm »

I want to try out different distro's since I haven't used Linux enough to really form an opinion on Gnome or the others.

Did you use the network install ISO?
I'm having issue's with the other two ISO options, they give an error when the installer just starts, preventing going any farther.
I haven't connected my Talos II to the internet yet, but maybe that's what I need to do.

22

Operating Systems and Porting / Re: [NEWS] AlmaLinux 8.5 now supports PowerPC

« on: March 19, 2022, 12:40:25 am »

Has anyone tried this out yet?

23

Talos II / Re: OpenBMC password

« on: March 15, 2022, 11:51:14 am »

That's for changing a password when you're already able to login, but I meant for recovering access and resetting a lost password.

24

Talos II / Re: OpenBMC password

« on: March 14, 2022, 09:50:35 pm »

It was a lowercase L.
For some reason I thought it was an uppercase L or maybe a '1' or 'I'. The 'one' is very similar.

I'm still curious on how logging into the serial console is suppose to allow you to reset the password though. I don't see any OpenBMC documentation about it. I found this: https://docs.graphcore.ai/projects/bmc-user-guide/en/latest/serial-rescue.html ...but is it specific to graphcore processors or generic to OpenBMC?

25

Talos II / Re: OpenBMC password

« on: March 13, 2022, 01:39:26 pm »

Yeah, I've tried different variation for the characters that look ambiguous, but still no luck logging in.

26

Talos II / OpenBMC password

« on: March 13, 2022, 03:13:09 am »

I'm trying to log in to the BMC on my new Talos II with the password that came in the box, but it doesn't work.

Are there instructions somewhere on setting/resetting the password? I've connected to the serial console port but don't see any obvious way in u-boot to do that.