406
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
407
General CPU Discussion / Re: Practical hardware and operating systems on Microwatt?
« on: June 09, 2020, 08:28:59 pm »408
User Zone / Re: Crackling sound with Kernel 5.6.x
« on: June 09, 2020, 11:14:29 am »
Should I post this on the Fedora ML?
409
General CPU Discussion / Re: Practical hardware and operating systems on Microwatt?
« on: June 09, 2020, 11:12:21 am »
Dunno, if you're on Twitter. Linux on Microwatt.
410
User Zone / Re: Crackling sound with Kernel 5.6.x
« on: June 09, 2020, 09:00:57 am »
No, the quality is good. The only thing was that from time to time speech-dispatcher appears in the GNOME settings audio. Then the audio sounds similar to the Bad.mp3. After I removed the speech-dispatcher everything was fine.
411
Operating Systems and Porting / Re: [NEWS] Fedora 32 is released
« on: June 09, 2020, 07:04:24 am »
Turned on the Computer. The display switched automatically to the AMD port. Then I got a black screen and I had to switch manually to the AST port to get a screen. After Petitboot I have to switch back to the AMD.
Normally -> Power on -> switch automatically to AST -> after Petitboot switch manually to AMD.
Normally -> Power on -> switch automatically to AST -> after Petitboot switch manually to AMD.
412
Operating Systems and Porting / Re: [NEWS] Fedora 32 is released
« on: June 08, 2020, 05:11:09 pm »
I have also connected both GPUs to my display. But no matter which Kernel I was using (Kernel 5.4/ 5.5 or Kernel 5.6.13+) I always had to manually switch between the GPUs.
I think that in my case both GPUs are active after switching on. Because every now and then (very rarely) the display switches to the AMD GPU at startup.
I think that in my case both GPUs are active after switching on. Because every now and then (very rarely) the display switches to the AMD GPU at startup.
413
User Zone / Re: Crackling sound with Kernel 5.6.x
« on: June 08, 2020, 04:54:06 pm »
Hi,
nothing special.
See link to the Kernel 5.4 alsa-info.sh output and Kernel 5.6 alsa-info.sh output
The only difference that I noticed while flying over it was:
Kernel 5.4:
Kernel 5.6:
Can a difference in IRQ cause this problem?
nothing special.
Code: [Select]
GRUB_CMDLINE_LINUX="rd.lvm.lv=fedora/root rd.lvm.lv=fedora/swap rhgb quiet"See link to the Kernel 5.4 alsa-info.sh output and Kernel 5.6 alsa-info.sh output
The only difference that I noticed while flying over it was:
Kernel 5.4:
Code: [Select]
0 [Generic ]: HDA-Intel - HD-Audio Generic
HD-Audio Generic at 0x600c0000a0000 irq 22Kernel 5.6:
Code: [Select]
0 [HDMI ]: HDA Intel - HDA ATI HDMI
HDA ATI HDMI at 0x600c0000a0000 irq 23Can a difference in IRQ cause this problem?
414
User Zone / Re: Crackling sound with Kernel 5.6.x
« on: June 07, 2020, 05:22:34 pm »
No. I think it's different. Two mp3s attached.
The quiet noise at the beginning comes from the recording. The slight crackling is like on an LP and the Bad.mp3 recording is totally distorted. Unfortunately I cannot reproduce it or provoke it. With Kernel 5.4 the sound is crystal clear.
The quiet noise at the beginning comes from the recording. The slight crackling is like on an LP and the Bad.mp3 recording is totally distorted. Unfortunately I cannot reproduce it or provoke it. With Kernel 5.4 the sound is crystal clear.
415
User Zone / Crackling sound with Kernel 5.6.x
« on: June 06, 2020, 10:45:07 am »
I have a problem with kernel 5.6 and sound output over a Navi RX 5500 GPU. It's a rustle/ distortion gets worse with echo. The whole thing disappears then becomes and then reappears. Sounds similar to speech-dispatcher being activated. But I have already deleted this one.
With kernel 5.4 this problem does not occur. Is the problem perhaps already known or how can I localize the problem?
dmesg output
Kernel 5.4: https://pastebin.com/H5F3VK3W
Kernel 5.6: https://pastebin.com/gnTv63NG
With kernel 5.4 this problem does not occur. Is the problem perhaps already known or how can I localize the problem?
dmesg output
Kernel 5.4: https://pastebin.com/H5F3VK3W
Kernel 5.6: https://pastebin.com/gnTv63NG
416
Blackbird / Re: power consumption figures?
« on: June 02, 2020, 06:38:16 pm »
I hardly guess, row four is also the complete (measured at the wall) system.
The top row is also the complete system (except a optical drive, minus RX5500 XT).
You can't compare measured at the wall with data reported by lm_sensors figures.
Data reported by lm_sensors is CPU alone, AFAIK.
You should compare row one with row four instead.
madscientist159 claims that the idle of 4-core and 8-core are identical, IIRC.
The top row is also the complete system (except a optical drive, minus RX5500 XT).
You can't compare measured at the wall with data reported by lm_sensors figures.
Data reported by lm_sensors is CPU alone, AFAIK.
You should compare row one with row four instead.
madscientist159 claims that the idle of 4-core and 8-core are identical, IIRC.
417
Blackbird / Re: power consumption figures?
« on: June 02, 2020, 08:21:39 am »
On the Blackbird page you will figures, too.
418
Blackbird / Re: How many fans per FAN header?
« on: May 23, 2020, 11:43:46 am »
I don't think this will make any difference. Because the bottleneck will still be the Y-cable and not the fan connector itself.
419
Blackbird / Re: [FEEDBACK] Failed to boot if J10116 pin header touches the card on 8X slot
« on: May 22, 2020, 07:48:42 am »
Yes. It's mentioned also here.
Also the USB2 port is blocking some cards ...
Also the USB2 port is blocking some cards ...
420
Blackbird / Re: Blackbird memory options...
« on: May 21, 2020, 05:06:33 pm »
I wouldn't look at speed, since most of them run at 2666MHz anyway.
I would buy as much RAM as I want to pay for it. I would buy 32GB (€130).
The performance is of course better if both slots are in use.
I would buy as much RAM as I want to pay for it. I would buy 32GB (€130).
The performance is of course better if both slots are in use.
